Difference between revisions of "SFE Footprint Library"
Jump to navigation
Jump to search
Line 3: | Line 3: | ||
List of current fp's: | List of current fp's: | ||
*5-Lead DD PAK - Voltage regulator | *5-Lead DD PAK - Voltage regulator | ||
− | 0603 - This is the basic 0603 footprint. Use this or 0603 - OLD1 | + | *0603 - This is the basic 0603 footprint. Use this or 0603 - OLD1 |
− | 0603 - LED | + | *0603 - LED |
− | 0603 - OLD1 - Original, tight 0603 layout. Works great, very minimal | + | *0603 - OLD1 - Original, tight 0603 layout. Works great, very minimal |
− | 1206 - LED - This is a very revised, nice layout for 1206 LEDs including an expanded paste layer for a nice solid solder connection | + | *1206 - LED - This is a very revised, nice layout for 1206 LEDs including an expanded paste layer for a nice solid solder connection |
− | 3216 EIA-A - Perfect for 10uF tantulum caps | + | *3216 EIA-A - Perfect for 10uF tantulum caps |
− | 7343 EIA-D - Perfect for 100uF tantulum caps | + | *7343 EIA-D - Perfect for 100uF tantulum caps |
− | Antenna - 2.4GHz - This is the antenna found on the RF-24G devices. No guarantees it will impedance match | + | *Antenna - 2.4GHz - This is the antenna found on the RF-24G devices. No guarantees it will impedance match |
− | Antenna - 2.45GHz - Chip antenna fp | + | *Antenna - 2.45GHz - Chip antenna fp |
− | Antenna - SMA - Vertical mount SMA or RP-SMA connector | + | *Antenna - SMA - Vertical mount SMA or RP-SMA connector |
− | Antenna - SMA - End Launch | + | *Antenna - SMA - End Launch |
− | BGA-32 - 32 ball bga for the Analog Device's ADXRS MEMs gyros | + | *BGA-32 - 32 ball bga for the Analog Device's ADXRS MEMs gyros |
− | BlueRadio with Antenna - This is the FP for the Bluetooth module. No guarantees. It's a bit odd with restricted areas. | + | *BlueRadio with Antenna - This is the FP for the Bluetooth module. No guarantees. It's a bit odd with restricted areas. |
− | CF Socket - Basic CF breakout. Start from here and make it fit your part | + | *CF Socket - Basic CF breakout. Start from here and make it fit your part |
− | CF Socket - Recommended - more silkscreen, wider solder pads | + | *CF Socket - Recommended - more silkscreen, wider solder pads |
− | CNZ1120 - Optical photo intr/sensor fp | + | *CNZ1120 - Optical photo intr/sensor fp |
− | Coin Cell Holder 12mm - SMD | + | *Coin Cell Holder 12mm - SMD |
− | Coin Cell Holder 20mm - PTH | + | *Coin Cell Holder 20mm - PTH |
− | Connector Molex x - Vertical and right angle connectors with polarized connectors | + | *Connector Molex x - Vertical and right angle connectors with polarized connectors |
− | DB9 Headers - various DB9 connector FPs include PTH and end launch | + | *DB9 Headers - various DB9 connector FPs include PTH and end launch |
− | DIN-3 - DIN connector | + | *DIN-3 - DIN connector |
− | DIP connectors | + | *DIP connectors |
− | GM862 - Cellular module FP with antenna, pin1 indicator, and shield holes (proven, works great!) | + | *GM862 - Cellular module FP with antenna, pin1 indicator, and shield holes (proven, works great!) |
− | Headers - Various SIP 0.1" headers | + | *Headers - Various SIP 0.1" headers |
− | Lassen iQ - Couple FPs for the Lassen iQ with and w/o silkscreen lines (proven, works great) | + | *Lassen iQ - Couple FPs for the Lassen iQ with and w/o silkscreen lines (proven, works great) |
− | LCC8 - Special - Minimal FP for the ADXL series accelerometers from Analog Devices (proven, works great) | + | *LCC8 - Special - Minimal FP for the ADXL series accelerometers from Analog Devices (proven, works great) |
− | LCD 16x2 - This is mechanical and electrical FP for 16x2 LCD from SFE. (proven, works great) | + | *LCD 16x2 - This is mechanical and electrical FP for 16x2 LCD from SFE. (proven, works great) |
− | LED Polarized - Simple T1, 5mm LED FP | + | *LED Polarized - Simple T1, 5mm LED FP |
− | LED Polarized 3mm - 3mm LED fp, works ok. Hard to see silkscreen | + | *LED Polarized 3mm - 3mm LED fp, works ok. Hard to see silkscreen |
− | LFCSP - Recommended and modified FP for the newer ADXL32x series from Analog Devices. Recommended FP is proven and works great. | + | *LFCSP - Recommended and modified FP for the newer ADXL32x series from Analog Devices. Recommended FP is proven and works great. |
− | microSD Socket - Proven, works great | + | *microSD Socket - Proven, works great |
− | MLP-24 - Used for the nRF2401-ish ICs from Nordic. Proven, works great | + | *MLP-24 - Used for the nRF2401-ish ICs from Nordic. Proven, works great |
− | MLP-28 - Used for the CP210x USB ICs from SI Labs. Proven, works great | + | *MLP-28 - Used for the CP210x USB ICs from SI Labs. Proven, works great |
− | PIC ICSP Mini - This is a custom FP by SFE. It's a in circuit serial programming jack that is 1.5mm pitch. Used to program just a bootloader onto a board without using up the space of a full sized programming header | + | *PIC ICSP Mini - This is a custom FP by SFE. It's a in circuit serial programming jack that is 1.5mm pitch. Used to program just a bootloader onto a board without using up the space of a full sized programming header |
− | Power Jack - common barrel jacks with silk and mechanical layers | + | *Power Jack - common barrel jacks with silk and mechanical layers |
− | Power Switch - Common SPDT switch, can be used for power or signal | + | *Power Switch - Common SPDT switch, can be used for power or signal |
− | QFN-16 - Used for the MMA7260Q triple axis accelerometer. Works great but has some interesting keepout lines to keep vias out from under the IC | + | *QFN-16 - Used for the MMA7260Q triple axis accelerometer. Works great but has some interesting keepout lines to keep vias out from under the IC |
− | QRD1114 - FP for the QRD1114 IR line sensor | + | *QRD1114 - FP for the QRD1114 IR line sensor |
− | QUAD44 - TQFP package for the 16F877A IC | + | *QUAD44 - TQFP package for the 16F877A IC |
− | Radial Caps - Various FPs for radial caps. Be sure your part matches the various dimensions. | + | *Radial Caps - Various FPs for radial caps. Be sure your part matches the various dimensions. |
− | RJ11 - Jack for ICD or telephone | + | *RJ11 - Jack for ICD or telephone |
− | Screw Terminal - 0.1" pitch screw terminal, two position version has two peg holes for structural stability | + | *Screw Terminal - 0.1" pitch screw terminal, two position version has two peg holes for structural stability |
− | SD-MMC Socket - Just what it sounds like | + | *SD-MMC Socket - Just what it sounds like |
− | SJ-2503A - 2.5mm stero jack | + | *SJ-2503A - 2.5mm stero jack |
− | SMA - Diode - Good 1A reverse polarized diode | + | *SMA - Diode - Good 1A reverse polarized diode |
− | SMD Cap - SMD eletrolytics. Use at your own risk | + | *SMD Cap - SMD eletrolytics. Use at your own risk |
− | SOD-323 - Very small diode, good for signals | + | *SOD-323 - Very small diode, good for signals |
− | SOIC - various soic FPs | + | *SOIC - various soic FPs |
− | Solder Jumper - NC - Normally closed solder jumper. The paste layer is expanded so during reflow, extra paste is available so the jumper is shorted | + | *Solder Jumper - NC - Normally closed solder jumper. The paste layer is expanded so during reflow, extra paste is available so the jumper is shorted |
− | Solder Jumper - NO - Normall Open solder jumper. Paste layer is there, but not enough for a short | + | *Solder Jumper - NO - Normall Open solder jumper. Paste layer is there, but not enough for a short |
− | Solder Switch - handy for SMD switches just using a soldering iron | + | *Solder Switch - handy for SMD switches just using a soldering iron |
− | SOT-23 - Commom BJT footprint with various configuration. Check the datasheet for your particular part. | + | *SOT-23 - Commom BJT footprint with various configuration. Check the datasheet for your particular part. |
− | SOT-23A - FP for popular small voltage regulators | + | *SOT-23A - FP for popular small voltage regulators |
− | SOT-223 - Bigger 1A voltage regulators use this footprint like the [[LM1117]] | + | *SOT-223 - Bigger 1A voltage regulators use this footprint like the [[LM1117]] |
− | SOT-457 - Transistor array FP | + | *SOT-457 - Transistor array FP |
− | SPDT Relay - Couple relay footprints | + | *SPDT Relay - Couple relay footprints |
− | SSOP - Various SSOP footprints | + | *SSOP - Various SSOP footprints |
− | Stencil Peg - This is an alignment hole for the Stencil-Alignment-System as well as a stand-off hole. | + | *Stencil Peg - This is an alignment hole for the Stencil-Alignment-System as well as a stand-off hole. |
− | Switch - Various momentary switch FPs. SMD, PTH, and Right Angle PTH | + | *Switch - Various momentary switch FPs. SMD, PTH, and Right Angle PTH |
− | Terminal Block - Various screw terminal blocks | + | *Terminal Block - Various screw terminal blocks |
− | TO-92 - Various v-reg and PTH transistor FPs | + | *TO-92 - Various v-reg and PTH transistor FPs |
− | TO-220 - Various PTH FPs including LM317, LM7805, and heat sinked FPs | + | *TO-220 - Various PTH FPs including LM317, LM7805, and heat sinked FPs |
− | TRF-24G - Popular FPs for the RF-24G 2.4GHz module | + | *TRF-24G - Popular FPs for the RF-24G 2.4GHz module |
− | Trim Pot - Couple trimpot FPs | + | *Trim Pot - Couple trimpot FPs |
− | USB - Various USB connector FPs | + | *USB - Various USB connector FPs |
− | WEEE Icon - The european initiative to limit electronics trash. It's an silkscreen icon that looks like a trash can... | + | *WEEE Icon - The european initiative to limit electronics trash. It's an silkscreen icon that looks like a trash can... |
− | Xtal-2 - Standard crystal FP | + | *Xtal-2 - Standard crystal FP |
− | Xtal-6 - SMD Watch crystal FP | + | *Xtal-6 - SMD Watch crystal FP |
− | Xtal-SMD8 - SMD ceramic resonator FP | + | *Xtal-SMD8 - SMD ceramic resonator FP |
− | Xtal-SMD9 - SMD quartz crystal FP | + | *Xtal-SMD9 - SMD quartz crystal FP |
Revision as of 14:02, 28 January 2006
This is the holy grail for SFE. Each footprint is a custom layout. This library has been compiled over 5 years and 100s of man hours worth of work. If you are a student, please, enjoy and learn. If you are a professional, please buy something from www.sparkfun.com to help us out.
List of current fp's:
- 5-Lead DD PAK - Voltage regulator
- 0603 - This is the basic 0603 footprint. Use this or 0603 - OLD1
- 0603 - LED
- 0603 - OLD1 - Original, tight 0603 layout. Works great, very minimal
- 1206 - LED - This is a very revised, nice layout for 1206 LEDs including an expanded paste layer for a nice solid solder connection
- 3216 EIA-A - Perfect for 10uF tantulum caps
- 7343 EIA-D - Perfect for 100uF tantulum caps
- Antenna - 2.4GHz - This is the antenna found on the RF-24G devices. No guarantees it will impedance match
- Antenna - 2.45GHz - Chip antenna fp
- Antenna - SMA - Vertical mount SMA or RP-SMA connector
- Antenna - SMA - End Launch
- BGA-32 - 32 ball bga for the Analog Device's ADXRS MEMs gyros
- BlueRadio with Antenna - This is the FP for the Bluetooth module. No guarantees. It's a bit odd with restricted areas.
- CF Socket - Basic CF breakout. Start from here and make it fit your part
- CF Socket - Recommended - more silkscreen, wider solder pads
- CNZ1120 - Optical photo intr/sensor fp
- Coin Cell Holder 12mm - SMD
- Coin Cell Holder 20mm - PTH
- Connector Molex x - Vertical and right angle connectors with polarized connectors
- DB9 Headers - various DB9 connector FPs include PTH and end launch
- DIN-3 - DIN connector
- DIP connectors
- GM862 - Cellular module FP with antenna, pin1 indicator, and shield holes (proven, works great!)
- Headers - Various SIP 0.1" headers
- Lassen iQ - Couple FPs for the Lassen iQ with and w/o silkscreen lines (proven, works great)
- LCC8 - Special - Minimal FP for the ADXL series accelerometers from Analog Devices (proven, works great)
- LCD 16x2 - This is mechanical and electrical FP for 16x2 LCD from SFE. (proven, works great)
- LED Polarized - Simple T1, 5mm LED FP
- LED Polarized 3mm - 3mm LED fp, works ok. Hard to see silkscreen
- LFCSP - Recommended and modified FP for the newer ADXL32x series from Analog Devices. Recommended FP is proven and works great.
- microSD Socket - Proven, works great
- MLP-24 - Used for the nRF2401-ish ICs from Nordic. Proven, works great
- MLP-28 - Used for the CP210x USB ICs from SI Labs. Proven, works great
- PIC ICSP Mini - This is a custom FP by SFE. It's a in circuit serial programming jack that is 1.5mm pitch. Used to program just a bootloader onto a board without using up the space of a full sized programming header
- Power Jack - common barrel jacks with silk and mechanical layers
- Power Switch - Common SPDT switch, can be used for power or signal
- QFN-16 - Used for the MMA7260Q triple axis accelerometer. Works great but has some interesting keepout lines to keep vias out from under the IC
- QRD1114 - FP for the QRD1114 IR line sensor
- QUAD44 - TQFP package for the 16F877A IC
- Radial Caps - Various FPs for radial caps. Be sure your part matches the various dimensions.
- RJ11 - Jack for ICD or telephone
- Screw Terminal - 0.1" pitch screw terminal, two position version has two peg holes for structural stability
- SD-MMC Socket - Just what it sounds like
- SJ-2503A - 2.5mm stero jack
- SMA - Diode - Good 1A reverse polarized diode
- SMD Cap - SMD eletrolytics. Use at your own risk
- SOD-323 - Very small diode, good for signals
- SOIC - various soic FPs
- Solder Jumper - NC - Normally closed solder jumper. The paste layer is expanded so during reflow, extra paste is available so the jumper is shorted
- Solder Jumper - NO - Normall Open solder jumper. Paste layer is there, but not enough for a short
- Solder Switch - handy for SMD switches just using a soldering iron
- SOT-23 - Commom BJT footprint with various configuration. Check the datasheet for your particular part.
- SOT-23A - FP for popular small voltage regulators
- SOT-223 - Bigger 1A voltage regulators use this footprint like the LM1117
- SOT-457 - Transistor array FP
- SPDT Relay - Couple relay footprints
- SSOP - Various SSOP footprints
- Stencil Peg - This is an alignment hole for the Stencil-Alignment-System as well as a stand-off hole.
- Switch - Various momentary switch FPs. SMD, PTH, and Right Angle PTH
- Terminal Block - Various screw terminal blocks
- TO-92 - Various v-reg and PTH transistor FPs
- TO-220 - Various PTH FPs including LM317, LM7805, and heat sinked FPs
- TRF-24G - Popular FPs for the RF-24G 2.4GHz module
- Trim Pot - Couple trimpot FPs
- USB - Various USB connector FPs
- WEEE Icon - The european initiative to limit electronics trash. It's an silkscreen icon that looks like a trash can...
- Xtal-2 - Standard crystal FP
- Xtal-6 - SMD Watch crystal FP
- Xtal-SMD8 - SMD ceramic resonator FP
- Xtal-SMD9 - SMD quartz crystal FP