Difference between revisions of "SFE Footprint Library"

From OpenCircuits
Jump to navigation Jump to search
Line 3: Line 3:
 
List of current fp's:
 
List of current fp's:
 
*5-Lead DD PAK - Voltage regulator
 
*5-Lead DD PAK - Voltage regulator
0603 - This is the basic 0603 footprint. Use this or 0603 - OLD1
+
*0603 - This is the basic 0603 footprint. Use this or 0603 - OLD1
0603 - LED
+
*0603 - LED
0603 - OLD1 - Original, tight 0603 layout. Works great, very minimal
+
*0603 - OLD1 - Original, tight 0603 layout. Works great, very minimal
1206 - LED - This is a very revised, nice layout for 1206 LEDs including an expanded paste layer for a nice solid solder connection
+
*1206 - LED - This is a very revised, nice layout for 1206 LEDs including an expanded paste layer for a nice solid solder connection
3216 EIA-A - Perfect for 10uF tantulum caps
+
*3216 EIA-A - Perfect for 10uF tantulum caps
7343 EIA-D - Perfect for 100uF tantulum caps
+
*7343 EIA-D - Perfect for 100uF tantulum caps
Antenna - 2.4GHz - This is the antenna found on the RF-24G devices. No guarantees it will impedance match
+
*Antenna - 2.4GHz - This is the antenna found on the RF-24G devices. No guarantees it will impedance match
Antenna - 2.45GHz - Chip antenna fp
+
*Antenna - 2.45GHz - Chip antenna fp
Antenna - SMA - Vertical mount SMA or RP-SMA connector
+
*Antenna - SMA - Vertical mount SMA or RP-SMA connector
Antenna - SMA - End Launch
+
*Antenna - SMA - End Launch
BGA-32 - 32 ball bga for the Analog Device's ADXRS MEMs gyros
+
*BGA-32 - 32 ball bga for the Analog Device's ADXRS MEMs gyros
BlueRadio with Antenna - This is the FP for the Bluetooth module. No guarantees. It's a bit odd with restricted areas.
+
*BlueRadio with Antenna - This is the FP for the Bluetooth module. No guarantees. It's a bit odd with restricted areas.
CF Socket - Basic CF breakout. Start from here and make it fit your part
+
*CF Socket - Basic CF breakout. Start from here and make it fit your part
CF Socket - Recommended - more silkscreen, wider solder pads
+
*CF Socket - Recommended - more silkscreen, wider solder pads
CNZ1120 - Optical photo intr/sensor fp
+
*CNZ1120 - Optical photo intr/sensor fp
Coin Cell Holder 12mm - SMD
+
*Coin Cell Holder 12mm - SMD
Coin Cell Holder 20mm - PTH
+
*Coin Cell Holder 20mm - PTH
Connector Molex x - Vertical and right angle connectors with polarized connectors
+
*Connector Molex x - Vertical and right angle connectors with polarized connectors
DB9 Headers - various DB9 connector FPs include PTH and end launch
+
*DB9 Headers - various DB9 connector FPs include PTH and end launch
DIN-3 - DIN connector
+
*DIN-3 - DIN connector
DIP connectors
+
*DIP connectors
GM862 - Cellular module FP with antenna, pin1 indicator, and shield holes (proven, works great!)
+
*GM862 - Cellular module FP with antenna, pin1 indicator, and shield holes (proven, works great!)
Headers - Various SIP 0.1" headers
+
*Headers - Various SIP 0.1" headers
Lassen iQ - Couple FPs for the Lassen iQ with and w/o silkscreen lines (proven, works great)
+
*Lassen iQ - Couple FPs for the Lassen iQ with and w/o silkscreen lines (proven, works great)
LCC8 - Special - Minimal FP for the ADXL series accelerometers from Analog Devices (proven, works great)
+
*LCC8 - Special - Minimal FP for the ADXL series accelerometers from Analog Devices (proven, works great)
LCD 16x2 - This is mechanical and electrical FP for 16x2 LCD from SFE. (proven, works great)
+
*LCD 16x2 - This is mechanical and electrical FP for 16x2 LCD from SFE. (proven, works great)
LED Polarized - Simple T1, 5mm LED FP
+
*LED Polarized - Simple T1, 5mm LED FP
LED Polarized 3mm - 3mm LED fp, works ok. Hard to see silkscreen
+
*LED Polarized 3mm - 3mm LED fp, works ok. Hard to see silkscreen
LFCSP - Recommended and modified FP for the newer ADXL32x series from Analog Devices. Recommended FP is proven and works great.
+
*LFCSP - Recommended and modified FP for the newer ADXL32x series from Analog Devices. Recommended FP is proven and works great.
microSD Socket - Proven, works great
+
*microSD Socket - Proven, works great
MLP-24 - Used for the nRF2401-ish ICs from Nordic. Proven, works great
+
*MLP-24 - Used for the nRF2401-ish ICs from Nordic. Proven, works great
MLP-28 - Used for the CP210x USB ICs from SI Labs. Proven, works great
+
*MLP-28 - Used for the CP210x USB ICs from SI Labs. Proven, works great
PIC ICSP Mini - This is a custom FP by SFE. It's a in circuit serial programming jack that is 1.5mm pitch. Used to program just a bootloader onto a board without using up the space of a full sized programming header
+
*PIC ICSP Mini - This is a custom FP by SFE. It's a in circuit serial programming jack that is 1.5mm pitch. Used to program just a bootloader onto a board without using up the space of a full sized programming header
Power Jack - common barrel jacks with silk and mechanical layers
+
*Power Jack - common barrel jacks with silk and mechanical layers
Power Switch - Common SPDT switch, can be used for power or signal
+
*Power Switch - Common SPDT switch, can be used for power or signal
QFN-16 - Used for the MMA7260Q triple axis accelerometer. Works great but has some interesting keepout lines to keep vias out from under the IC
+
*QFN-16 - Used for the MMA7260Q triple axis accelerometer. Works great but has some interesting keepout lines to keep vias out from under the IC
QRD1114 - FP for the QRD1114 IR line sensor
+
*QRD1114 - FP for the QRD1114 IR line sensor
QUAD44 - TQFP package for the 16F877A IC
+
*QUAD44 - TQFP package for the 16F877A IC
Radial Caps - Various FPs for radial caps. Be sure your part matches the various dimensions.
+
*Radial Caps - Various FPs for radial caps. Be sure your part matches the various dimensions.
RJ11 - Jack for ICD or telephone
+
*RJ11 - Jack for ICD or telephone
Screw Terminal - 0.1" pitch screw terminal, two position version has two peg holes for structural stability
+
*Screw Terminal - 0.1" pitch screw terminal, two position version has two peg holes for structural stability
SD-MMC Socket - Just what it sounds like
+
*SD-MMC Socket - Just what it sounds like
SJ-2503A - 2.5mm stero jack
+
*SJ-2503A - 2.5mm stero jack
SMA - Diode - Good 1A reverse polarized diode
+
*SMA - Diode - Good 1A reverse polarized diode
SMD Cap - SMD eletrolytics. Use at your own risk
+
*SMD Cap - SMD eletrolytics. Use at your own risk
SOD-323 - Very small diode, good for signals
+
*SOD-323 - Very small diode, good for signals
SOIC - various soic FPs
+
*SOIC - various soic FPs
Solder Jumper - NC - Normally closed solder jumper. The paste layer is expanded so during reflow, extra paste is available so the jumper is shorted
+
*Solder Jumper - NC - Normally closed solder jumper. The paste layer is expanded so during reflow, extra paste is available so the jumper is shorted
Solder Jumper - NO - Normall Open solder jumper. Paste layer is there, but not enough for a short
+
*Solder Jumper - NO - Normall Open solder jumper. Paste layer is there, but not enough for a short
Solder Switch - handy for SMD switches just using a soldering iron
+
*Solder Switch - handy for SMD switches just using a soldering iron
SOT-23 - Commom BJT footprint with various configuration. Check the datasheet for your particular part.
+
*SOT-23 - Commom BJT footprint with various configuration. Check the datasheet for your particular part.
SOT-23A - FP for popular small voltage regulators
+
*SOT-23A - FP for popular small voltage regulators
SOT-223 - Bigger 1A voltage regulators use this footprint like the [[LM1117]]
+
*SOT-223 - Bigger 1A voltage regulators use this footprint like the [[LM1117]]
SOT-457 - Transistor array FP
+
*SOT-457 - Transistor array FP
SPDT Relay - Couple relay footprints
+
*SPDT Relay - Couple relay footprints
SSOP - Various SSOP footprints
+
*SSOP - Various SSOP footprints
Stencil Peg - This is an alignment hole for the Stencil-Alignment-System as well as a stand-off hole.
+
*Stencil Peg - This is an alignment hole for the Stencil-Alignment-System as well as a stand-off hole.
Switch - Various momentary switch FPs. SMD, PTH, and Right Angle PTH
+
*Switch - Various momentary switch FPs. SMD, PTH, and Right Angle PTH
Terminal Block - Various screw terminal blocks
+
*Terminal Block - Various screw terminal blocks
TO-92 - Various v-reg and PTH transistor FPs
+
*TO-92 - Various v-reg and PTH transistor FPs
TO-220 - Various PTH FPs including LM317, LM7805, and heat sinked FPs
+
*TO-220 - Various PTH FPs including LM317, LM7805, and heat sinked FPs
TRF-24G - Popular FPs for the RF-24G 2.4GHz module
+
*TRF-24G - Popular FPs for the RF-24G 2.4GHz module
Trim Pot - Couple trimpot FPs
+
*Trim Pot - Couple trimpot FPs
USB - Various USB connector FPs
+
*USB - Various USB connector FPs
WEEE Icon - The european initiative to limit electronics trash. It's an silkscreen icon that looks like a trash can...
+
*WEEE Icon - The european initiative to limit electronics trash. It's an silkscreen icon that looks like a trash can...
Xtal-2 - Standard crystal FP
+
*Xtal-2 - Standard crystal FP
Xtal-6 - SMD Watch crystal FP
+
*Xtal-6 - SMD Watch crystal FP
Xtal-SMD8 - SMD ceramic resonator FP
+
*Xtal-SMD8 - SMD ceramic resonator FP
Xtal-SMD9 - SMD quartz crystal FP
+
*Xtal-SMD9 - SMD quartz crystal FP

Revision as of 13:02, 28 January 2006

This is the holy grail for SFE. Each footprint is a custom layout. This library has been compiled over 5 years and 100s of man hours worth of work. If you are a student, please, enjoy and learn. If you are a professional, please buy something from www.sparkfun.com to help us out.

List of current fp's:

  • 5-Lead DD PAK - Voltage regulator
  • 0603 - This is the basic 0603 footprint. Use this or 0603 - OLD1
  • 0603 - LED
  • 0603 - OLD1 - Original, tight 0603 layout. Works great, very minimal
  • 1206 - LED - This is a very revised, nice layout for 1206 LEDs including an expanded paste layer for a nice solid solder connection
  • 3216 EIA-A - Perfect for 10uF tantulum caps
  • 7343 EIA-D - Perfect for 100uF tantulum caps
  • Antenna - 2.4GHz - This is the antenna found on the RF-24G devices. No guarantees it will impedance match
  • Antenna - 2.45GHz - Chip antenna fp
  • Antenna - SMA - Vertical mount SMA or RP-SMA connector
  • Antenna - SMA - End Launch
  • BGA-32 - 32 ball bga for the Analog Device's ADXRS MEMs gyros
  • BlueRadio with Antenna - This is the FP for the Bluetooth module. No guarantees. It's a bit odd with restricted areas.
  • CF Socket - Basic CF breakout. Start from here and make it fit your part
  • CF Socket - Recommended - more silkscreen, wider solder pads
  • CNZ1120 - Optical photo intr/sensor fp
  • Coin Cell Holder 12mm - SMD
  • Coin Cell Holder 20mm - PTH
  • Connector Molex x - Vertical and right angle connectors with polarized connectors
  • DB9 Headers - various DB9 connector FPs include PTH and end launch
  • DIN-3 - DIN connector
  • DIP connectors
  • GM862 - Cellular module FP with antenna, pin1 indicator, and shield holes (proven, works great!)
  • Headers - Various SIP 0.1" headers
  • Lassen iQ - Couple FPs for the Lassen iQ with and w/o silkscreen lines (proven, works great)
  • LCC8 - Special - Minimal FP for the ADXL series accelerometers from Analog Devices (proven, works great)
  • LCD 16x2 - This is mechanical and electrical FP for 16x2 LCD from SFE. (proven, works great)
  • LED Polarized - Simple T1, 5mm LED FP
  • LED Polarized 3mm - 3mm LED fp, works ok. Hard to see silkscreen
  • LFCSP - Recommended and modified FP for the newer ADXL32x series from Analog Devices. Recommended FP is proven and works great.
  • microSD Socket - Proven, works great
  • MLP-24 - Used for the nRF2401-ish ICs from Nordic. Proven, works great
  • MLP-28 - Used for the CP210x USB ICs from SI Labs. Proven, works great
  • PIC ICSP Mini - This is a custom FP by SFE. It's a in circuit serial programming jack that is 1.5mm pitch. Used to program just a bootloader onto a board without using up the space of a full sized programming header
  • Power Jack - common barrel jacks with silk and mechanical layers
  • Power Switch - Common SPDT switch, can be used for power or signal
  • QFN-16 - Used for the MMA7260Q triple axis accelerometer. Works great but has some interesting keepout lines to keep vias out from under the IC
  • QRD1114 - FP for the QRD1114 IR line sensor
  • QUAD44 - TQFP package for the 16F877A IC
  • Radial Caps - Various FPs for radial caps. Be sure your part matches the various dimensions.
  • RJ11 - Jack for ICD or telephone
  • Screw Terminal - 0.1" pitch screw terminal, two position version has two peg holes for structural stability
  • SD-MMC Socket - Just what it sounds like
  • SJ-2503A - 2.5mm stero jack
  • SMA - Diode - Good 1A reverse polarized diode
  • SMD Cap - SMD eletrolytics. Use at your own risk
  • SOD-323 - Very small diode, good for signals
  • SOIC - various soic FPs
  • Solder Jumper - NC - Normally closed solder jumper. The paste layer is expanded so during reflow, extra paste is available so the jumper is shorted
  • Solder Jumper - NO - Normall Open solder jumper. Paste layer is there, but not enough for a short
  • Solder Switch - handy for SMD switches just using a soldering iron
  • SOT-23 - Commom BJT footprint with various configuration. Check the datasheet for your particular part.
  • SOT-23A - FP for popular small voltage regulators
  • SOT-223 - Bigger 1A voltage regulators use this footprint like the LM1117
  • SOT-457 - Transistor array FP
  • SPDT Relay - Couple relay footprints
  • SSOP - Various SSOP footprints
  • Stencil Peg - This is an alignment hole for the Stencil-Alignment-System as well as a stand-off hole.
  • Switch - Various momentary switch FPs. SMD, PTH, and Right Angle PTH
  • Terminal Block - Various screw terminal blocks
  • TO-92 - Various v-reg and PTH transistor FPs
  • TO-220 - Various PTH FPs including LM317, LM7805, and heat sinked FPs
  • TRF-24G - Popular FPs for the RF-24G 2.4GHz module
  • Trim Pot - Couple trimpot FPs
  • USB - Various USB connector FPs
  • WEEE Icon - The european initiative to limit electronics trash. It's an silkscreen icon that looks like a trash can...
  • Xtal-2 - Standard crystal FP
  • Xtal-6 - SMD Watch crystal FP
  • Xtal-SMD8 - SMD ceramic resonator FP
  • Xtal-SMD9 - SMD quartz crystal FP