| Latest revision |
Your text |
| Line 1: |
Line 1: |
| − | {| align=right
| + | Hello! |
| − | |-
| + | Excellent site, but most of messages here are not related to its contents... |
| − | |
| |
| − | [[Image:PG31-PowerSupply.jpg|300px|TPS Voltage Regulator]]
| |
| − | |}
| |
| − | <b>Description:</b><br> These large current, high voltage diodes can be used for a multitude of purposes. Really, we just use them for reverse polarization protection.
| |
| | | | |
| − | Most systems that we play with are DC based - whatever board requires 'X' voltage (3.3V for example). The board expects the DC voltage in a certain way. VCC in one spot, ground in another. If you reverse this (attaching VCC where GND should be, etc) ''BAD'' things happen. If you're lucky, there will be a massive short somewhere and nothing major will smoke. If you're unlucky, the board will go up in smoke and some things might explode. In practice, most things heat up (no smoke or explosion), but are instantly killed. So now you've got a board that doesn't work but it can be very hard (nye, nearly impossible) to tell what is damaged and what can be fixed.
| + | [http://garners.bb-fr.com free gay mpeg clips] | |
| − | | + | [http://www.gb-x.de/gbuch.php?forum_id=76256 black gay escorts] | |
| − | Obviously there must be a way to prevent this from happening. Enter diodes...
| + | [http://icehousee5e.www2.prexon.nl/ nude gay men fucking] | |
| − | | + | [http://www.guestbook.at/gb/gast/index.php?buchid=atrophies66 dirty gay sex] |
| − | These pieces of silicon allow current to flow in one direction only. Quite simply, VCC is allowed through but GND is not. Why don't we put a diode on every VCC? Well a diode can cause a 0.7V drop (that's what they teach you in silly eng school at least) on the power line. So if you are dealing with a really low-power system, 0.7V drop can be too much.
| |
| − | | |
| − | There are other ways to protect against reverse polarization like polarized connectors and certain voltage regulators have protection built in. But it you're designing something for mass-market where you don't know who will be connecting what, a reverse protection diode is cheap and easily designed into a board.
| |
| − | | |
| − | [[Image:PG31-PowerSupply-Schematic.jpg]] | |
| − | | |
| − | Here you can see the diode D3 in place, directly connected to the [[Barrel Power Jack]].
| |
| − | | |
| − | These type diodes can also be used, four at a time, in an [http://en.wikipedia.org/wiki/Diode_bridge bridge rectifier] configuration. I don't have a good image (now you do), but an bridge rectifier takes an AC signal and rectifies it to a DC signal (neat trick actually). A bridge rectifier circuit will also work with a DC supply. This allows the "reverse protection" trick to become an "I don't care" trick -- whichever way the polarity of the input voltage is, the circuit will still work. The downside is that you lose 2 diode drops or about 1.3V. NOTE -- you have to disconnect the input power from ground to make this work.
| |
| − | | |
| − | Diodes come in all shapes and sizes. For this posting, we only care about cheap, bulky, large current diodes. These diodes can handle 1-2A each and are cheap. For some our mass designs, we prefer the surface mount diodes (MBRA140). The MBRA140 comes in an SMA package (hopelessly confused with the SMA antenna connector - who came up with this?!). Many other diodes come in axial packages perfect for bread boarding. They all work the same - there is an anode and a cathode. I was always told to remember the <b>a</b>node is the <b>a</b>rrow, the bar is the cathode, and current flows in the direction of the arrow. Cool huh?
| |
| − | | |
| − | We like the MBRA140 cause it's cheap and can handle up to 1A. One amp is overkill for most applications, but that's why it's good, it'll work with most applications. If you need something less burly, Digikey/Mouser has more than plenty. Be sure to get a diode that is current rated for the max current draw of your system. If the diode is too small, it'll heat up and eventually burn out.
| |
| − | | |
| − | Dropping 0.7V is wasteful, and it becomes more significant the lower the power supply. If the design will operate on batteries, then dropping 0.7V might not even allow the circuit to work. What do you do in this case? There are two options:
| |
| − | | |
| − | 1. Use Schottky diodes instead of standard ones. A Schottky will only drop around 0.3V and there are some than can drop even less voltage than that. Cheap, simple!<br>
| |
| − | 2. When even 0.3V won't do it, then use a transistor! Use a P-mosfet and control the base using either discrete components or an LTC4412 for only 20mV of voltage drop. The pitfall with this is the added power consumption of the LTC4412 and the cost, but for most cases the 28uA are insignificant.:<br>
| |
| − | | |
| − | <b>Documents:</b><br>
| |
| − | [[Media:Mbra140tr.pdf|MBRA140 Datasheet]] | |
| − | | |
| − | <b>Footprints:</b><br>
| |
| − | [[SFE_Footprint_Library|SFE Footprint Library]]
| |
| − | | |
| − | FP Name: SMA-Diode
| |
| − | | |
| − | <b>Manufacturer Info:</b><br>
| |
| − | International Rectifier # : MBRA140TR<br>
| |
| − | | |
| − | <b>Supplier Info:</b><br>
| |
| − | Digikey part # : MBRA140CT-ND<br>
| |
| − | Single Piece Price : $0.45
| |
| − | | |
| − | <b>Related Items:</b><br>
| |
| − | | |
| − | [[Category:Components]]
| |
