Programming the Device

From OpenCircuits
Revision as of 00:49, 15 January 2009 by Nelson (talk | contribs)
Jump to navigation Jump to search

Requirements

Hardware

  1. PC with COM port (Windows XP Installed for MPLAB)
  2. ICD2 Programmer
  3. Target Board
  4. 5V Power Supply

Software

  1. MPLAB IDE v7.50: v7.60 is not compatible with our current ICD2 Programmers. There are consistent "Devices cannot be founded" warnings.
  2. dsPicProgrammer (dsPicProgrammer.jar)

Files

  1. dsPicBootloader (bl_5011.hex). Original assembly code by ingenia can be downloaded from here.
  2. Application hex file (e.g. app.hex)


Loading Bootloader (Once only)

Loading Bootloader
Step Remarks
Install MPLAB IDE
  • Do NOT connect ICD 2 (via USB) to PC
  • Execute MPLAB vX.XX Install.exe
Install USB Driver
  • Follow the instruction in (C:\Program Files\Microchip\MPLAB IDE\ICD2\Drivers\Ddicd2.htm)
Select Target Chip
  • Run MPLAB IDE on PC
  • Select: Configure>Select Devices...
  • Choose dsPIC30F5011
Target <-> ICD 2
  • Use six pin cable. Beware of the pin assignments. Only pin 1 - 5 should be used.
  • Place Jumper on target board (if any). The Jumper connects target Vcc to ICD 2.
  • Do NOT power-up the target.
ICD 2 <-> PC
  • Plug-in ICD 2 to PC via USB cable
  • Power-up the target.
  • Select: Programmer>Select Programmer>MPLAB ICD 2
  • If this is the first time the ICD 2 is connected to PC, MPLAB IDE will automatically download the required OS to ICD 2, wait until it has finished
  • If you have not connected and powered up the target, you might see Warnings on invalid device IDs, and/or running self tests.
  • See results of self test if necessary: Programmer>Settings, Status Tab. Refer to ICD2 User's Guide Chapter 7.
Load Bootloader
  • Select: File>Import...
  • Select bl_5011.hex
Start Programming
  • Select: Programmer>Program
Finishing
  • Power-down the Taget
  • Select: Programmer>Select Programmer>None
  • Unplug USB cable

Hardware Setting

DSC00921.JPG

  • Connect your usb to rs232 cable to your computer

Download Loading Firmware

Windows Vista

1.jpg

  • Go to Control Panel \ Device Manager

2.jpg

  • Find out your Device comm port Number

File:3.jpg

  • Open a command prompt

4.jpg

  • Run dsPicProgrammer
    • Input cd Desktop\dsPic_production\dsPicProgrammer

5.jpg

  • Loading Firmware
    • Input jre\bin\java -Djava.library.path=.\rxtx\bin -jar dspicProgrammer.jar COM1 115200 ./firmware/foo.hex
    • eg. jre\bin\java -Djava.library.path=.\rxtx\bin -jar dspicProgrammer.jar COM9 115200 ./firmware/8072303.hex
where COM9 is your COM Port ID
115200 is communication speed [in bps]
foo.hex is your firmware new file

6.jpg

  • Enter Y to comfirm

2 6 complete.JPG

  • Wait until programming is completed.
  • after all completed, power OFF your device, then power ON again, enjoy your new updated.


Windows XP

e.g. desktop
  • Unzip the dsPic_Programmer.zip, then you have an unziped file.

File:Prog guid dl.JPG


  • Drag the unzip file to a director.
eg. USB memory devics

Prog guid drag.JPG


  • Save your .hex file(foo.hex) to your directory location
e.g. X:\dsPic_Programmer\ ---> X:\ is the driver where the dsPic_Programmer located

Prog guid hex.JPG

Download Firmware

  • Start a Command Prompt
  • Run dsPicProgrammer
    • Make sure your device is connected through a "Direct RS232 Cable" to PC Serial Port.
    • Change to the directory where dsPicProgrammer.jar is located and run the command:
      • for example, jre\bin\java -Djava.library.path=.\rxtx\bin -jar dspicProgrammer.jar COM1 115200 foo.hex
      • Or directly using dsPicProgrammer.bat COM1 115200 foo.hex(Windows)
      • java -jar dsPicProgrammer.jar /dev/ttyS0 115200 foo.hex (Linux)
where COM1 is your COM Port ID
115200 is communication speed [in bps]
foo.hex is your firmware new file
2 3 command.JPG
  • When the program prompt you for an input, press y:
    File:2 4 prompt.JPG
  • If communication can be established, you should see something like this:
    2 5 progress.JPG
  • Wait until programming is completed.
    2 6 complete.JPG
  • after all completed, power OFF your device, then power ON again, enjoy your new updated.

Troubleshooting

Invalid COM Port

  • In case of selecting an invalid COM port, you should see the error message:
    gnu.io.NoSuchPortException: Choosing COM Port Error
    3 1 com err.JPG

Missing firmware file

  • In case of selecting a firmware file that does not exist, you should see the error message:
    java.io.FileNotFoundException: foo1.hex <The system cannot find the file specified>
    3 2 file err.JPG

Missing RXTX driver

  • In case of missing the RXTX driver, you should see the error message:
    Exception in thread “main” java.lang.NoClassDefFoundError: gnu/io/UnsupportedCommOperationException
    3 3 rxtx err.JPG