meridia free wwe ringtones phentermine online xanax online hydrocodone online zanaflex online free ringtones buy didrex free real ringtones buy fioricet buy diazepam cheap rivotril ativan online sonyericsson ringtones free sagem ringtones verizon ringtones free sharp ringtones ortho online cheap wellbutrin valium online nexium online tracfone ringtones sony ericsson ringtones cool ringtones zoloft free motorola ringtones qwest ringtones free samsung ringtones nextel ringtones cheap celexa free ericsson ringtones free midi ringtones tenuate online levitra online adipex online free punk ringtones cheap propecia cheap albuterol alprazolam online viagra online tramadol online sony ringtones ambien online free funny ringtones hgh online polyphonic ringtones cheap cialis free nokia ringtones but flexeril online norco cheap ultracet cheap carisoprodol free kyocera ringtones clonazepam online pharmacy online online cheap cyclobenzaprine cheap ultram cheap lisinopril xenical online cheap zyban mono ringtones lorazepam online free sprint ringtones lipitor online order prozac free music ringtones hoodia online vigrx online diethylpropion online but lortab cheap vicodin free mtv ringtones free alltel ringtones soma online free jazz ringtones sildenafil online paxil online free mp3 ringtones cheap clomid cingular ringtones There are many kinds of motor drivers:
- servo motor controller
- stepper motor controller
- DC motor controller ("brushed")
- AC motor controller ("brushless")
- ... (todo: fill in the other kinds) ...
A DC motor controller that is 'reversable' generally uses an 'H bridge'. This 'H-bridge' uses four output drivers in a configuration that resembles an H where the load is the cross bar in the middle. The lines on either side of the load (the downward strokes in the H) represent a series connection of a pull-up driver and a pull-down driver. This allows each terminal of the load to be connected to either the positive supply rail, or the negative supply rail. This allows a positive, negative or zero voltage difference across the load. This load voltage is then utilised to provide the desired control required of the motor. The various combinations can give a 'forwards' torque on a DC motor, a 'backwards' torque on the same motor, can allow the motor to free-wheel (without any applied torque) or can provide a locking of the motor such that it resists any attempt to rotate it.
A single phase AC motor is generally driven in the same way as a DC motor, however instead of operating the motor drive as a constant DC voltage (in either the 'forward' or 'reverse' direction) the AC motor is driven by an approximation to a sinewave. This approximation is created using the H bridge and driving it with a PWM input such that both the positive and negative voltage periods are the same. This is normally acheived either using a sawtooth waveform compared against a sine wave reference, or is done using a lookup table in a microcontroller.
A similar method is used to drive multiphase (3-phase) AC motors, however instead of just using an H bridge, only a half H bridge is used per phase. Each phases half bridge is then driven in the same manner as for the single phase motor, with a phase difference between the phases as appropriate.
((fill in more details here...))
Some motor controller circuits are such that, if the software accidentally sets the "wrong" pins hi or lo, you get a short circuit through the output drivers. This will generally cause a high current to flow, due to the low on state resistance of the output drivers, which may destroy other electronic components before finally blowing the supply fuse.
Other motor controller circuits are such that, if the software accidentally sets the "wrong" pins hi or lo, the worst that could happen is the motor spins the wrong way. These circuits are designed so that, no matter what the inputs, it is impossible to get a short circuit through the output drivers. Between "one branch on" and "the other branch on", there is a minimum "blanking time" which has "both branches off". This guarantees that we never have "both branches on" (short circuit).
Guess which type of design I prefer?
A random collection of semi-related links (please prune out the irrelevant ones):
- H-Bridge by Bob Blick
- the Open Source Motor Controller Project
- LiniStepper $30 each; Open Source! Circuit Diagram, PCB (Board) Layout, and PIC Software all available. Nice photos of the LiniStepper at http://www.piclist.com/techref/io/stepper/linistep/lini_bld.htm .
- H-Bridge Fundamentals An in-depth article on the design of Mosfet H-Bridges
- PMinMO.com Open Source circuits and information on stepper motor controllers]
- ePanorama ePanorama Motor Control page
- "Electronic Design of DC Motor Drives" has detailed schematics and PCB layout for a system that has a PC send commands through the serial port to a Microchip PICmicro, which does PWM control of 2 H bridges. Each half-bridge uses a IRF9530N (100V 14A pfet plus flyback diode) and a IRF530 (IRF530NPBF: 100V 17A nfet plus flyback diode), driven by a small transistor inverter based on a BD135 npn, for a total of 12 discrete transistors.
Robots use motor drivers.