Linuxstamp II 9260

From OpenCircuits
Revision as of 15:23, 22 March 2010 by Linuxvolts (talk | contribs)
Jump to navigation Jump to search

Linuxstamp 9260 top.JPG Linuxstamp 9260 bottom.JPG

Description

The Linuxstamp is designed to be a general purpose processor module. It is designed to work as a stand alone module (micro-SD card, Ethernet and USB/Serial converter are all on the module). This allows all initial development to be done without a motherboard, but for integration into a specific project a motherboard with specific features could be designed.

Status

You can now purchase Linuxstamp II boards from thelinuxstamp.com. Some of the original Linuxstamp info is still useful.

Features

  • Atmel AT91SAM9260 processor (Arm9 processor with MMU, 200Mhz operation)
  • 32MB SDRAM
  • 256MB NAND Flash
  • 1x 10/100 Ethernet
  • 1x USB host port (allows wifi adapters, flash drives and other USB devices to be used)
  • 1x micro-SD card slot
  • Serial debug port 5-pin header
  • JTAG port

Emdebian

The current Linux distribution is Emdebian. It is located in the NAND flash and uses UBI & UBIFS.

License

All files for this project are licensed under the GNU GPL V2

Hardware design files

Warning!!! Use this design at your own risk. Errata: a 10k pull-up resistor is needed on the CMD line to use the uSD card. Here are the design files You can view the pdf of the schematic here

Power

The power supply for the board is based on the Linear LTC3407-3. This is a very compact high frequency switching power supply. It has both a 3.3v and a 1.8v output. It does have a very tight input range 3.3v-5.5v. The Micrel PHY also needs 2.5v, but this is provided by an internal regulator. Currently a regulated 5v must be used to power the board.

Minicom & the debug port

Ftdi cable.jpeg

Above shows the proper connection of the ftdi cable to the Linuxstamp II. This provides both the debug console as well as power to the board. Pin 6 (green wire) on the cable overhangs the 5-pin connector on the board.

When you plug the Linuxstamp into your host (Linux) machine a device should appear /dev/ttyUSB0 (the suffix number will increment as you add more devices). /dev/ttyUSB0 will behave as any other serial port now. Minicom is the standard program to access the serial port in Linux. The first time you run minicom you will have to be root in order to do the setup, after that you can change the permissions on /dev/ttyUSB0 so any user can run minicom. To enter configuration mode in minicom type CTRL-A o, now scroll down to Serial port setup. Use the letters to navigate. You will want the device to be /dev/ttyUSB0 and Bps/Par/Bits to read 115200 8N1. Both hardware and software flow control should be OFF. Connection to the board is important for loading Atmel's tiny program and u-boot, but once the board is working it might not be as important.

Another alternative is to use HyperTerm on Windows, which works fine with the Hardware boot loader. If you are updating the Darren Bootloader, note that the loader only has a short delay after you initiate the "receive" (on the loader) after which it send out the "ready to receive" signal. As a result, you'll need to be rather quick to initiate the Xmodem "send" (on HyperTerm). If you are seeing time outs on HyperTerm when you try and send the loader.bin file, you are probably hitting this problem ... you need to have initiated the send before you see the "C" on the screen from the bootloader.

nfs & tftp

Nfs (network file system) and tftp (trivial file transfer protocol) are two servers you will want running on your host machine. Nfs is useful for hosting the root file system of the Linuxstamp. Tftp is useful for u-boot to retrieve the kernel from. There are many other websites on nfs and tftp, but I will try and go over a simple setup. I would suggest being behind a firewall before trying either of these setups as neither is secure. I wrote this using a Fedora 7 system. First make sure you have nfs installed.

$ yum install nfs-utils nfs-utils-lib portmap system-config-nfs

On Ubuntu (or other debian-style systems) you could use:

$ sudo apt-get install portmap nfs-kernel-server nfs-common

Now to make sure the service is enabled run (this won't work on Ubuntu):

$ serviceconf and make sure nfs and nfs lock are checked

Now edit /etc/exports you should add a line like this /path_to_nfs_root/ *(rw,no_root_squash,insecure). Now restart nfs.

$ sudo /etc/init.d/nfs restart

You can test that it is set up correctly by typing the following on the local system (i.e. right on the NFS server)

$ showmount -e localhost

You can test this from a remote system with

$ mount -t nfs server_name:/path_to_nfs_root /path_to_test_mount

Now on to tftp. Make sure it is installed.

$ yum install tftp-server

This will create a file /etc/xinetd.d/tftp. In this file you will want to change disable from yes to no. Now make a test file.

$ cd /tftpboot
$ echo hello > file

Now we can test it

$ tftp -v server_name -c get tmp

Now with u-boot we can load image files

> tftpboot 20800000 uImage

And boot them

> bootm 20800000

NAND Flash

One good solution for the NAND flash is to use the new ubi and ubifs components. These both need to be enabled in the kernel, and then they can be used from the emdebian system. You can always check what mtd devices are avaliable in /proc/mtd. First we can format the mtd device:

$ ubiformat /dev/mtd1

Now we can "attach" it. This is telling the kernel to use the ubi subsystem for that partition. The -m 1 says use /dev/mtd1.

$ ubiattach /dev/ubi_ctrl -m 1

Now we can make a volume. As it says on the linux-mtd page you can only mount a ubi volume not a mtd device or a ubi device:

$ ubimkvol /dev/ubi0 -N rootfs -s 244MiB

Now the volume can be mounted

$ mount -t ubifs ubi0_0 /mnt/tmp/


Links

Discussion

Please join the google group for the Linuxstamp discussion http://groups.google.com/group/linuxstamp

Contact

For further questions or comments please contact Paul (pthomas8589 _at_ gmail _dot_ com)

other boards that run Linux